Skip to content
FederalSpecial noticeClosed Federal notice

TECHNOLOGY LICENSING OPPORTUNITY: AddiSteel HT

Department of Energy› Triad - DOE Contractor Los Alamos, NM

Solicitation # S-133632Updated May 5, 2026

This RFP closed on Jun 5, 2026.

The details below are kept for reference. Similar open RFPs are listed first.

Closed

Jun 5, 2026

Responses were due Jun 5, 2026, 5:00 PM MDT

Posted
May 5, 2026
Closed
Jun 5, 2026

Similar open RFPs

Same NAICS group or Supplies, Equipment & Furniture, nearby first, ranked by score.

Strong

NASA-White Sands Scrap Metal Removal Term Contract

Federal Acquisition Service · Las Cruces, NM

FederalIFBSupplies, Equipment & Furniture
Posted Nov 20Due Dec 21, 2026, 5:00 PM CST (in 29 days)Federal notice
Fair

Fetal Monitor - Zuni Comprehensive Community Health Center (ZCCHC)

Indian Health Service · Zuni, NM

FederalSources soughtIndian Small Business Economic EnterpriseSupplies, Equipment & Furniture+1
Posted Nov 16Due Dec 1, 2026, 12:30 PM MST (in 9 days)Federal notice
Fair

Technology Licensing Opportunity

Department of Energy · Los Alamos, NM

FederalSpecial noticeSupplies, Equipment & Furniture
Posted Oct 6Due Mar 6, 2027, 5:00 PM MST (in 105 days)Federal notice

RFP Detector Scores are informational.How we score →

Summary by RFP Detector

What this RFP is about

Department of Energy (Triad - DOE Contractor) posted a special notice titled “TECHNOLOGY LICENSING OPPORTUNITY: AddiSteel HT” under solicitation number S-133632. It was posted on May 5, 2026. The response deadline was Jun 5, 2026, 5:00 PM MDT. It is classified under NAICS 332117 (Powder Metallurgy Part Manufacturing) and product/service code AG13. No set-aside is listed. The place of performance is Los Alamos, New Mexico. The listed point of contact is Satya Srinivasan.

Key facts

Sector
Federal
Notice type
Special notice
As posted: Special Notice
PSC
AG13
Place of performance
Los Alamos, NM
ZIP 87545
Value
Not stated
Solicitation #
S-133632
Listing
Official federal notice

Score at publication

Score breakdown

Every RFP starts at 50. Each factor adds or subtracts points compared with a typical RFP; unknown data counts as neutral.

Frozen at publication: closed RFPs are not re-scored.

Starts at 50

  • Value0.0unknown

    No value published, and there isn't enough award history to estimate one. Scored as neutral.

  • Competition & access−0.6estimated

    Full and open competition.

  • Issuer & market+3.2estimated

    83 other RFPs from Department of Energy on RFP Detector in the past 12 months; no award history found.

  • Time & stage+1.4measured

    Special notice: 31 days to respond (due Jun 5, 2026, 5:00 PM MDT).

  • Clarity & completeness+4.7estimated

    Documents not listed, 2 named contacts with email, 732-word description.

  • Freshness+9.0measured

    Posted today.

50 + contributions = 68 (B, Strong)

Informational, not advice to bid or not bid. Score version 1.0.0, evaluated May 5, 2026.

Requirements & submission

Eligibility · Full and open competition

Full and open competition means the notice states no set-aside: any responsible business can respond, subject to the requirements in the notice.

Not stated in a form we could extract. See the official solicitation for requirements, evaluation criteria and submission steps.

From the official notice

Description

732 words

Additively Manufactured Ferritic Steel with Enhanced High-Temperature Performance Grade 91 steel is one of the most widely used structural metals in power plants and candidate for advanced nuclear reactors, but it loses much of its strength when operating temperatures climb above 500°C. Researchers at Los Alamos National Laboratory solved that problem by 3D-printing Grade 91 steel using a powder bed fusion process with carefully tuned laser settings. The rapid heating and cooling that occurs during printing creates a microstructure unlike anything achievable through traditional steelmaking, and the printed steel is up to 85% stronger at 600°C than its conventionally made counterpart while remaining just as ductile. A granted U.S. patent (US 11,471,946 B2) protects both the manufacturing method and the resulting material. Value Proposition AddiSteel HT gives manufacturers the ability to produce complex steel parts that hold up far better under extreme heat than today’s standard materials. Because the process uses commercially available Grade 91 powder and standard industrial 3D printers, adoption does not require exotic raw materials or entirely new equipment. The performance gains are significant enough that printed ferritic steel could serve as a lower-cost alternative to nickel-based superalloys in many high-temperature applications, opening the door to lighter, cheaper and more geometrically creative component designs across the energy and industrial sectors. How it Works A laser selectively melts thin layers of steel powder, one on top of another, to build a solid part from the ground up. LANL’s innovation lies in a proprietary combination of laser power, scanning speed and layer orientation that produces an unusually fine and complex grain structure with a combination of ductile and strong grains during printing. The steels thermal history during the build process creates the microstructure distribution of around 80 % by volume Bainitic grains with a uniform distribution of second phase particles and dislocations, surrounded by 20 % by volume Martensitic grains. This is fundamentally different from what conventional casting or forging can achieve. Each new layer also partially heat-treats the layer beneath it, so the finished part may need little or no additional processing before use. Technical Description Conventional Grade 91 steel relies on a tempered martensite structure that loses strength significantly at high temperatures. The additive process instead produces a layered architecture containing multiple distinct microstructural zones within each laser pass, including regions with extremely fine grains, regions rich in strengthening precipitates and small pockets of martensite at the boundaries between passes. Working together, these features resist deformation at elevated temperatures far more effectively than the uniform microstructure of wrought steel. Testing confirms the advantage across the board. At 600°C, the printed steel reaches a yield strength of 650 MPa versus 350 MPa for the wrought version. Even after being held at 650°C for 1000 hours — a test simulating long-term service — the printed material retains 650 MPa of yield strength at room temperature. The patent covers process parameters for both Grade 91 and Grade 92 steel compositions, broadening the range of potential applications. Advantages Up to 85% stronger at 600 °C than conventionally processed Grade 91 steel Stronger and more ductile at the same time, avoiding the usual tradeoff between strength and ductility Potential to replace costly nickel superalloys in many high-heat applications, reducing material expense Complex shapes printed directly from digital designs, cutting machining waste and production lead times Proven thermal stability after extended high-temperature exposure Works with multiple steel grades, including Grade 91 and Grade 92 Market Applications Nuclear Energy (reactor components, fuel cladding, steam generators) Power Generation (boiler piping, turbine parts, heat exchangers) Automotive and Transportation (exhaust system components, turbocharger housings) Oil, Gas and Chemical Processing (high-temperature piping, pressure vessels) Aerospace and Defense (structural parts exposed to extreme heat) Industrial Manufacturing (custom tooling, high-heat process equipment) TRL 5 U.S. Patent No. 11,471,946 LA-UR-26-23628 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search

Documents

No documents are listed for this notice.

Contacts

2 contacts

Points of contact as published on the notice.

Timeline & history

  1. Special Notice posted

  2. Responses were due

More from Department of Energy

139 open RFPs from this issuer and its offices.

Limited

Dilo Gas Cart Training and Maintenance Services

Department of Energy

FederalSpecial noticeEducation & Training
Posted Nov 19Due Nov 23, 2026, 11:30 AM MST (in 26 h)Federal notice
Limited

Outdoor IR Dome Camera and Adapter

Department of Energy · Oak Ridge, TN

FederalCombined synopsisSupplies, Equipment & Furniture
Posted Nov 16Due Nov 23, 2026, 5:00 PM EST (in 30 h)Federal notice
Poor

Radio Detection Kit with Accessories - No Alternatives

Department of Energy · New York

FederalSolicitationSupplies, Equipment & Furniture
Posted Nov 4Due Nov 23, 2026, 5:00 PM EST (in 30 h)Federal notice
Limited

Mounting Pads

Department of Energy · Oak Ridge, TN

FederalSolicitationSupplies, Equipment & Furniture
Posted Sep 3Due Nov 24, 2026, 12:00 PM EST (in 2 days)Federal notice
Limited

ITRON Software Maintenance Renewal

Department of Energy

FederalSpecial noticeIT & Software
Posted Nov 17Due Nov 24, 2026, 12:00 PM CST (in 2 days)Federal notice
Poor

Poplar Williston Project

Department of Energy

FederalSolicitationSmall business set-asideSupplies, Equipment & Furniture+1
Posted Nov 10Due Nov 24, 2026, 11:30 AM MST (in 2 days)Federal notice

RFP Detector Scores are informational.How we score →

About this notice

Official federal notice. Updated May 5, 2026.

Official solicitation:Sign in free to open the official solicitation

RFP Detector is an independent service and is not affiliated with any government agency. Scores are informational.

RFP Detector is not affiliated with the organization that issued this RFP. Always rely on the official notice and confirm every date and requirement with the issuer.