Skip to content
FederalSpecial noticeClosed Federal notice

TECHNOLOGY LICENSING OPPORTUNITY: Engineered Porous Print Materials

Department of Energy› Triad - DOE Contractor Los Alamos, NM

Solicitation # S-133569Updated May 4, 2026

This RFP closed on Jun 4, 2026.

The details below are kept for reference. Similar open RFPs are listed first.

Closed

Jun 4, 2026

Responses were due Jun 4, 2026, 5:00 PM MDT

Posted
May 4, 2026
Closed
Jun 4, 2026

Similar open RFPs

Same NAICS group or Supplies, Equipment & Furniture, nearby first, ranked by score.

Limited

TECHNOLOGY LICENSING OPPORTUNITY: GasFlow DLP Printing Interface

Department of Energy · Los Alamos, NM

FederalSpecial noticeSupplies, Equipment & Furniture
Posted Nov 6Due Apr 6, 2027, 5:00 PM MDT (in 135 days)Federal notice
Strong

NASA-White Sands Scrap Metal Removal Term Contract

Federal Acquisition Service · Las Cruces, NM

FederalIFBSupplies, Equipment & Furniture
Posted Nov 20Due Dec 21, 2026, 5:00 PM CST (in 29 days)Federal notice
Fair

Fetal Monitor - Zuni Comprehensive Community Health Center (ZCCHC)

Indian Health Service · Zuni, NM

FederalSources soughtIndian Small Business Economic EnterpriseSupplies, Equipment & Furniture+1
Posted Nov 16Due Dec 1, 2026, 12:30 PM MST (in 9 days)Federal notice
Fair

Technology Licensing Opportunity

Department of Energy · Los Alamos, NM

FederalSpecial noticeSupplies, Equipment & Furniture
Posted Oct 6Due Mar 6, 2027, 5:00 PM MST (in 105 days)Federal notice

RFP Detector Scores are informational.How we score →

Summary by RFP Detector

What this RFP is about

Department of Energy (Triad - DOE Contractor) posted a special notice titled “TECHNOLOGY LICENSING OPPORTUNITY: Engineered Porous Print Materials” under solicitation number S-133569. It was posted on May 4, 2026. The response deadline was Jun 4, 2026, 5:00 PM MDT. It is classified under NAICS 333248 (All Other Industrial Machinery Manufacturing) and product/service code AC34. No set-aside is listed. The place of performance is Los Alamos, New Mexico. The listed point of contact is Satya Srinivasan.

Key facts

Sector
Federal
Notice type
Special notice
As posted: Special Notice
PSC
AC34
Place of performance
Los Alamos, NM
ZIP 87545
Value
Not stated
Solicitation #
S-133569
Listing
Official federal notice

Score at publication

Score breakdown

Every RFP starts at 50. Each factor adds or subtracts points compared with a typical RFP; unknown data counts as neutral.

Frozen at publication: closed RFPs are not re-scored.

Starts at 50

  • Value0.0unknown

    No value published, and there isn't enough award history to estimate one. Scored as neutral.

  • Competition & access−0.6estimated

    Full and open competition.

  • Issuer & market+3.2estimated

    83 other RFPs from Department of Energy on RFP Detector in the past 12 months; no award history found.

  • Time & stage+1.4measured

    Special notice: 31 days to respond (due Jun 4, 2026, 5:00 PM MDT).

  • Clarity & completeness+5.0estimated

    Documents not listed, 2 named contacts with email, 806-word description.

  • Freshness+9.0measured

    Posted today.

50 + contributions = 68 (B, Strong)

Informational, not advice to bid or not bid. Score version 1.0.0, evaluated May 4, 2026.

Requirements & submission

Eligibility · Full and open competition

Full and open competition means the notice states no set-aside: any responsible business can respond, subject to the requirements in the notice.

Not stated in a form we could extract. See the official solicitation for requirements, evaluation criteria and submission steps.

From the official notice

Description

806 words

Engineered Porous Print Materials enables manufacturers to produce complex, high-surface-area structures with precisely engineered porosity at macro, micro and nano scales — all from a single printable composition and a standard stereolithography printer. By eliminating the need for secondary coatings, multi-step mold processes or specialized equipment, this technology developed by Los Alamos National Laboratory simplifies the production of advanced porous materials while opening design possibilities that conventional fabrication methods cannot achieve. Organizations seeking to improve the performance of catalytic reactors, filtration systems, thermal management devices, energy storage components or biomedical scaffolds, to name a few, can now access a versatile, low-cost platform that translates digital designs directly into functional, multi-material foam structures with tunable chemistry and architecture. How it Works The process begins with a specially formulated resin that contains three key ingredients mixed together: a polymer precursor that can be hardened by light, a porogenic solvent that induces phase separation during hardening, and a structural precursor (such as a metal salt or ceramic precursor) that will ultimately form the skeleton of the final part. When loaded into a commercial SLA 3D printer, the resin is cured layer by layer using light, producing a printed intermediate structure composed of a nanoporous polymer gel with the structural precursor distributed uniformly throughout. Post-printing processing — which may include controlled heating, chemical reduction or catalytic treatments depending on the target material — converts the structural precursor into the desired solid (metal, ceramic or carbon) while decomposing and removing the polymer gel. The spaces formerly occupied by the polymer gel become a second, finer tier of porosity nested inside the larger pores defined by the printed geometry, and additional processing steps such as de-alloying can introduce a third, nanoscale tier of porosity. The entire workflow uses a single resin formulation with no need to add coatings or secondary materials after printing. Technical Description The printable composition is engineered so that the polymer precursor component (typically an acrylate monomer such as polyethylene glycol diacrylate) undergoes photopolymerization in the presence of a porogenic solvent (such as dimethylformamide or water) that is deliberately chosen for its low compatibility with the resulting polymer network. During curing, the polymer phase-separates from the solvent, creating a sponge-like gel with pore sizes and volumes that can be tuned by adjusting the solvent-to-monomer ratio, solvent chemistry and the inclusion of structure-directing additives. A photoinitiator and a polymerization quenching compound (an absorber dye) are included to control layer thickness and prevent unwanted curing beyond the intended print pattern. The structural precursor — which can be a dissolved metal salt, a pre-ceramic alkoxide, a carbonaceous precursor or a pre-metal oxide — is homogeneously incorporated within the gel phase during printing, enabling an “inside-out” assembly of the final material, or could be absorbed through wicking into the porous, spongelike material before post processing. After printing, downstream thermal and chemical treatments convert the structural precursor into the target material and remove the polymer template. For metal-based products, heating reduces metal ions to colloidal particles within the gel; further sintering fuses those particles into a continuous metallic skeleton while the polymer decomposes, leaving behind a free-standing porous metal replica of the original printed geometry. Isotropic shrinkage during polymer removal can reduce feature sizes well below the printer's native resolution, enabling structural details that conventional SLA cannot achieve on its own. Demonstrated material systems include silver, gold (with trimodal porosity achieved through silver-gold de-alloying), silica, boron carbide, copper, iron and cobalt oxide. Pore diameters span from greater than one millimeter at the macro scale down to below 100 nanometers at the nano scale, and all pore networks remain interconnected and accessible throughout the bulk of the part. Advantages Single-resin workflow instead of multiple coating steps Multi-scale porosity in one printed part Works across several material types Compatible with standard stereolithography equipment Internal pores stay connected and accessible Pore size and density can be adjusted through formulation and processing Market Applications Catalysis (reactor supports, flow-through catalyst bodies) Energy Storage (battery electrodes, capacitor structures) Thermal Management (heat exchangers, heat pipe wicks, cooling components) Filtration and Separations (fluid filters, gas scrubbers, purification media) Biomedical (bone scaffolds, culture substrates) Lightweight Structures (reinforcement, insulation, fire protection parts) U.S. Patent Nos. 11,267,920; 12,054,569; pending LA-UR-26-23577 TRL 4 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search

Documents

No documents are listed for this notice.

Contacts

2 contacts

Points of contact as published on the notice.

Timeline & history

  1. Special Notice posted

  2. Responses were due

More from Department of Energy

139 open RFPs from this issuer and its offices.

Limited

Dilo Gas Cart Training and Maintenance Services

Department of Energy

FederalSpecial noticeEducation & Training
Posted Nov 19Due Nov 23, 2026, 11:30 AM MST (in 26 h)Federal notice
Limited

Outdoor IR Dome Camera and Adapter

Department of Energy · Oak Ridge, TN

FederalCombined synopsisSupplies, Equipment & Furniture
Posted Nov 16Due Nov 23, 2026, 5:00 PM EST (in 30 h)Federal notice
Poor

Radio Detection Kit with Accessories - No Alternatives

Department of Energy · New York

FederalSolicitationSupplies, Equipment & Furniture
Posted Nov 4Due Nov 23, 2026, 5:00 PM EST (in 30 h)Federal notice
Limited

Mounting Pads

Department of Energy · Oak Ridge, TN

FederalSolicitationSupplies, Equipment & Furniture
Posted Sep 3Due Nov 24, 2026, 12:00 PM EST (in 2 days)Federal notice
Limited

ITRON Software Maintenance Renewal

Department of Energy

FederalSpecial noticeIT & Software
Posted Nov 17Due Nov 24, 2026, 12:00 PM CST (in 2 days)Federal notice
Poor

Poplar Williston Project

Department of Energy

FederalSolicitationSmall business set-asideSupplies, Equipment & Furniture+1
Posted Nov 10Due Nov 24, 2026, 11:30 AM MST (in 2 days)Federal notice

RFP Detector Scores are informational.How we score →

About this notice

Official federal notice. Updated May 4, 2026.

Official solicitation:Sign in free to open the official solicitation

RFP Detector is an independent service and is not affiliated with any government agency. Scores are informational.

RFP Detector is not affiliated with the organization that issued this RFP. Always rely on the official notice and confirm every date and requirement with the issuer.